This calculator works out the decibel level of a sound from its intensity or pressure, and also lets you compare two sound levels to find the difference in decibels. You enter the sound intensity in watts per square meter or the sound pressure in pascals, and you get the corresponding decibel value on the standard dB scale. It also computes the decibel difference between two sources, which is useful for adding or comparing sound levels.
Formula
For sound intensity, the decibel level is calculated using the formula:
L = 10 × log₁₀(I / I₀)
Where:
- L = sound level in decibels (dB)
- I = sound intensity in watts per square meter (W/m²)
- I₀ = reference intensity, typically 10⁻¹² W/m² (the threshold of human hearing)
For sound pressure, the formula is:
L = 20 × log₁₀(P / P₀)
Where:
- L = sound pressure level in decibels (dB SPL)
- P = root-mean-square sound pressure in pascals (Pa)
- P₀ = reference pressure, typically 20 µPa (2 × 10⁻⁵ Pa), the threshold of hearing at 1 kHz
The key difference is the factor of 20 for pressure versus 10 for intensity. This is because power (intensity) is proportional to the square of pressure, and the logarithm of a square doubles the result.
Worked Example
Using the default values from the calculator above, let’s find the decibel level of a sound with an intensity of 0.001 W/m² (which is about the intensity of a loud conversation or a vacuum cleaner).
Step 1: Identify the values.
- I = 0.001 W/m²
- I₀ = 10⁻¹² W/m²
Step 2: Divide the intensity by the reference.
0.001 / 10⁻¹² = 10⁹
Step 3: Take the base-10 logarithm.
log₁₀(10⁹) = 9
Step 4: Multiply by 10.
10 × 9 = 90 dB
So a sound with intensity 0.001 W/m² is 90 dB. The calculator shows 90.00, confirming the result.
Now, let’s find the difference between this and a second sound with intensity 0.01 W/m² (10 times more intense).
Step 1: Divide the second intensity by the first.
0.01 / 0.001 = 10
Step 2: Take the logarithm.
log₁₀(10) = 1
Step 3: Multiply by 10.
10 × 1 = 10 dB
So the second sound is 10 dB louder than the first. This matches the calculator’s output of 10.00.
When to Use This
Use this calculator whenever you need to convert a physical sound measurement into decibels. Common situations include:
- Interpreting sound intensity measurements from a microphone or acoustic sensor.
- Converting sound pressure readings from a sound level meter (in Pa) to dB SPL.
- Comparing two sound sources to see how many decibels apart they are.
- Understanding how adding multiple sources affects the total level (though that requires summing intensities first).
The decibel scale is logarithmic because human hearing perceives loudness roughly logarithmically. A 10 dB increase sounds about twice as loud to most people, and it corresponds to a tenfold increase in intensity.
How to Read the Result
The result is a dimensionless number, but it’s always relative to the reference you chose. For intensity, the standard reference is 10⁻¹² W/m², which is near the threshold of hearing at 1 kHz. For pressure, the standard reference is 20 µPa.
Here are some typical levels for reference (approximate):
- 0 dB: threshold of hearing
- 30 dB: quiet whisper
- 60 dB: normal conversation
- 90 dB: lawnmower or loud concert
- 120 dB: jet engine at close range (pain threshold)
Remember that decibels are relative, not absolute. A sound at 90 dB is 10 dB louder than one at 80 dB, but 100 times more intense (because 10 dB = 10× intensity, and 20 dB = 100× intensity).
Common Mistakes
- Using the wrong factor: For intensity, use 10 × log₁₀. For pressure, use 20 × log₁₀. Mixing them gives results that are off by a factor of 2 in the exponent.
- Forgetting to use the same units: The reference intensity is in W/m², and the reference pressure is in Pa. If you enter milliwatts or millipascals, convert first.
- Using the wrong reference: Some fields use different references (e.g., dBm for milliwatts, dBV for volts). This calculator uses the standard acoustic references.
- Confusing intensity and pressure: Intensity is power per area; pressure is force per area. They are related but not the same.
- Adding decibels directly: You cannot add dB values for two sources. You must convert back to intensity, add the intensities, then convert again. For example, two 80 dB sources do not make 160 dB; they make about 83 dB.
Tips
- For pressure readings, make sure you use the RMS (root-mean-square) value, not the peak value. Most sound level meters report RMS.
- If you’re comparing two sounds, always use the same reference and the same type (both intensity or both pressure).
- When adding multiple sound sources, first convert each to intensity (I = I₀ × 10^(dB/10)), sum them, then convert back to dB.
- Use the calculator to check your own mental math: every 10 dB increase means 10× more intensity, and every 3 dB increase means roughly 2× more intensity.
- For quick estimates, remember that a 1 dB change is barely perceptible, 3 dB is noticeable, and 10 dB is perceived as twice as loud.
Troubleshooting
Result is negative: This happens when the input intensity or pressure is below the reference. That’s valid—it means the sound is quieter than the reference level. For example, 10⁻¹³ W/m² gives -20 dB. If you expected a positive value, check that your input is larger than the reference.
Result is 0 dB: The input equals the reference exactly. That’s correct.
Result shows “Cannot compute”: This occurs when the second intensity is lower than the first, making the ratio less than 1 and the logarithm negative. The calculator prevents a negative difference because you asked for a difference. If you want the absolute difference, swap the two values or use the absolute value of the result.
You get an error when entering a value: Make sure the value is a positive number (or zero) and within the allowed range. The calculator rejects negative intensities because they are physically impossible.
You’re using pressure but the result seems too high or low: Check that you selected “Pressure” in the measurement type. If you leave it on “Intensity” and enter a pressure value in pascals, the result will be wrong because the formulas differ.
Frequently Asked Questions
What is the difference between dB and dB SPL?
dB is a general unit for any logarithmic ratio. dB SPL specifically refers to sound pressure level with the standard reference of 20 µPa. When people say “decibels” for sound, they usually mean dB SPL.
Why is the decibel scale logarithmic?
Because human hearing perceives loudness in a roughly logarithmic way, and the range of sound intensities we can hear spans about 10¹² (a trillion) times. A linear scale would be unwieldy.
Can I add two decibel values directly?
No. Decibels are logarithmic, so you must convert to linear intensity, add the intensities, then convert back. For two equal sources, the increase is about 3 dB.
What does 0 dB mean?
0 dB means the sound intensity equals the reference (10⁻¹² W/m²) or the pressure equals the reference (20 µPa). It’s the threshold of hearing for a typical young adult at 1 kHz, but it’s not absolute silence.
How do I convert from dB to intensity?
Use the inverse formula: I = I₀ × 10^(dB/10). For example, 60 dB with I₀ = 10⁻¹² gives I = 10⁻¹² × 10⁶ = 10⁻⁶ W/m².
Why does a 10 dB increase sound twice as loud?
Psychoacoustic studies show that most listeners perceive a 10 dB increase as approximately a doubling of loudness, even though the physical intensity increases tenfold. This is a rule of thumb, not an exact law.
Related
Formula used
in type | Measurement type | Intensity=1, Pressure=2 in val | Sound intensity (W/m²) | W/m² | 0.001 | 0 | 1e12 in ref | Reference intensity (W/m²) | W/m² | 1e-12 | 1e-15 | 1 out dB | Decibel level | dB | 10 * log10(val / ref) | 2 in val2 | Second intensity (W/m²) | W/m² | 0.01 | 0 | 1e12 out diff | Difference (dB) | dB | 10 * log10(val2 / val) | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.
- LDL to HDL Ratio: What It Means & How to Calculate It2.00
- Kappa to Lambda Ratio: What It Means & How to Use It
- Jasmine Rice to Water Ratio: Perfect Every Time1.50 cups
- How to Find Decibels from Intensity
- How to Do S/Z Ratio: A Step-by-Step Guide1.25
- How to Convert to Decibels (dB) Easily