help-calc

08 Numbers and Units

20 Slope to Ratio Conversions Explained

Card 08-0285 · Updated · Standard formula, shown below

Slope Ratio (run:rise) 4.00
Slope Percent
25.00 %
Result, rounded to 2 decimal places
Slope Angle
14.04 °
Result, rounded to 2 decimal places
Rise (vertical)
1 ft
Input
You enter
Rise (vertical) (ft), Run (horizontal) (ft)
You get
Slope Ratio (run:rise), Slope Percent (%), Slope Angle (°)
Rounding
2 dp

This guide covers 20 common slope-to-ratio conversions, from gentle drainage slopes to steep roof pitches. You’ll learn how to convert percent slope, degrees, and rise-over-run into ratio form (like 4:1 or 1:4) using simple formulas. It’s written for DIYers, engineers, landscapers, and students who need quick, accurate conversions without digging through textbooks.

Formula

Slope ratio is expressed as run:rise (horizontal distance to vertical rise). To convert from rise and run, divide run by rise. For example, a rise of 1 foot over a run of 4 feet gives a ratio of 4:1. Slope percent is (rise / run) × 100, and slope angle in degrees is the arctangent of (rise / run).

Worked Example

Using the default values: rise = 1 ft, run = 4 ft.
Ratio = 4 / 1 = 4:1
Percent = (1 / 4) × 100 = 25%
Angle = atan(1/4) = 14.04°

1. 1:1 Slope (45°)

A 1:1 slope means equal rise and run, giving a 45° angle. This is the steepest commonly used slope in landscaping and is often the maximum for walkable terrain without handrails.

2. 2:1 Slope (63.4°)

Common in embankments and retaining wall backfill. The run is twice the rise, so the angle is about 63.4°. This is steeper than the angle of repose for most soils, so it needs reinforcement.

3. 3:1 Slope (71.6°)

Often used for drainage channels and ditches. A 3:1 slope is quite steep and may erode quickly without riprap or vegetation. The angle is about 71.6°.

4. 4:1 Slope (75.9°)

This is a common slope for highway medians and berms. It’s steep enough to shed water but still allows mowing with specialized equipment. Angle: 75.9°.

5. 5:1 Slope (78.7°)

Used for some roof pitches and industrial ramps. A 5:1 slope is very steep for walking; it’s more of a climb than a walk. Angle: 78.7°.

6. 10:1 Slope (84.3°)

Nearly vertical. Used for retaining walls and some architectural features. The ratio means 10 units horizontal for every 1 unit vertical. Angle: 84.3°.

7. 100% Slope (45°)

A 100% slope equals a 1:1 ratio and a 45° angle. This is the classic conversion: percent slope = rise/run × 100. So 100% means rise equals run.

8. 50% Slope (26.6°)

Half of 100% – a rise of 1 unit over a run of 2 units. Ratio is 2:1. Angle: 26.6°. This is a typical maximum for wheelchair ramps (though code requires less).

9. 25% Slope (14.0°)

Rise of 1 over run of 4, ratio 4:1. This is a common slope for accessible ramps (1:12 is actually 8.33%, but 25% appears in some industrial settings). Angle: 14.0°.

10. 10% Slope (5.7°)

Rise of 1 over run of 10, ratio 10:1. Often used for road grades and parking lots. Angle: 5.7°.

11. 5% Slope (2.9°)

Rise of 1 over run of 20, ratio 20:1. This is a typical maximum for sidewalks and pedestrian paths. Angle: 2.9°.

12. 1% Slope (0.57°)

Rise of 1 over run of 100, ratio 100:1. Used for drainage on large roofs and parking lots. Angle: 0.57°.

13. 0.5% Slope (0.29°)

Common for concrete flatwork to ensure water runoff. Ratio is 200:1. Angle: 0.29°.

14. 1/4 inch per foot (2.08%)

Standard fall for plumbing pipes and some gutters. Over 1 foot (12 inches), rise is 0.25 inches. Ratio: 48:1 (run:rise). Angle: 1.19°.

15. 1/8 inch per foot (1.04%)

Minimum slope for some drainage tiles. Rise per foot is 0.125 inches. Ratio: 96:1. Angle: 0.60°.

16. 3/4 inch per foot (6.25%)

Often used for roof pitches in snowy climates. Rise per foot is 0.75 inches. Ratio: 16:1. Angle: 3.58°.

17. 6:12 Roof Pitch (26.6°)

Roof pitch is given as rise over 12 inches of run. A 6:12 pitch means 6 inches rise per foot. Convert to ratio: run:rise = 12:6 = 2:1. Angle: 26.6°.

18. 12:12 Roof Pitch (45°)

A steep roof pitch where rise equals run (12 inches per foot). Ratio: 1:1. Angle: 45°. Common in A-frame houses.

19. 4:12 Roof Pitch (18.4°)

Moderate roof pitch. Rise of 4 inches per foot. Ratio: 3:1 (run:rise). Angle: 18.4°.

20. 2:12 Roof Pitch (9.5°)

Low-slope roof, often requiring special waterproofing. Rise of 2 inches per foot. Ratio: 6:1. Angle: 9.5°.

How to Choose

Pick the conversion method based on what you know. If you have rise and run measurements, use the calculator above. If you have a percent slope, divide 100 by the percent to get the run:rise ratio (e.g., 25% → 100/25 = 4:1). For degrees, use the tangent: ratio = 1 / tan(angle). Always note whether the ratio is expressed as run:rise or rise:run – the order matters. For construction, check local codes for maximum allowed slopes.

Frequently Asked Questions

Q: How do I convert percent slope to ratio?
A: Divide 100 by the percent. For 25%, 100/25 = 4, so ratio is 4:1 (run:rise).

Q: What does a 1:20 slope mean?
A: It means for every 20 units horizontal, there is 1 unit vertical. This equals a 5% slope.

Q: Is a 2% slope the same as 1:50?
A: Yes. 2% = 2/100 = 1/50, so ratio is 50:1.

Q: How do I convert degrees to a ratio?
A: Use the tangent. For an angle θ, ratio = 1 / tan(θ). For 45°, tan(45°)=1, so ratio is 1:1.

Q: What is the difference between rise:run and run:rise?
A: Rise:run is vertical over horizontal (like roof pitch). Run:rise is horizontal over vertical (like accessibility ramps). They are reciprocals.

Q: What is a 1/4 inch per foot slope in ratio?
A: 1/4 inch per foot = 0.25 inches / 12 inches = 0.0208 = 2.08%. Ratio = 12/0.25 = 48:1.

Final Thoughts

Understanding slope-to-ratio conversions is essential for any project involving grading, drainage, or construction. Use the calculator for quick checks, and remember to double-check the order of your ratio. With these 20 examples, you’ll be prepared for most common situations.

Related

Formula used
in rise | Rise (vertical) | ft | 1 | 0 | 1000
in run | Run (horizontal) | ft | 4 | 0.01 | 10000
out ratio | Slope Ratio (run:rise) | - | run / rise | 2
out pct | Slope Percent | % | (rise / run) * 100 | 2
out deg | Slope Angle | ° | atand(rise / run) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.

More on this shelf

The whole Numbers and Units shelf →